However, balance is key and adding additional solutions can affect this requirement. Aside from algae, the presence of minerals in the water can cause the water to turn green.
This change in color is not accompanied by slime but just the alteration in color. The introduction of minerals such as iron, manganese or copper, can be the result of the green appearance of your hot tub water.
Copper can be introduced into the water from copper pipes or heat exchangers and natural well water. It is also possible for central water to be the carrier of these minerals. Additionally, the corrosion of pool equipment or pipes can also play a role in the presence of these minerals in your hot tub water. Manganese offers discoloration as well, but it is not usually green.
A black, brown or purple hue is an indication that this mineral is in your hot tub water. These minerals could be from copper pipes, the corrosion of equipment or even just minerals from your household water. Fake tanning products are also a big no go! The chemicals in your hot tub will remove the tan from your skin and turn your hot tub shell, pipework, and internal systems brown or green.
If your water has been green for less than 24 hours then you may be able to bring it back around again. Remove your pillows and use 60g of your sanitiser chlorine or bromine per 1,l of water. Leave the hot tub cover off for at least 20minutes and put the jets on for one cycle.
You will need to leave the hot tub for a few hours, if this has worked you will see the hot tub water begin to clear within 12 hours.
Once clear and the sanitiser has dropped to a safe level, you can use the hot tub again. If the water has been green for over 24 hours or the above has not worked then the best way to clear green water from your tub is to drain, clean thoroughly and then refill with fresh new water. Make sure the filters are cleaned and wipe down the interior so that any remaining algae is removed. Make sure to add your sanitiser and balance the pH once the hot tub has reached temperature.
The main reason you could have cloudy hot tub water is just because the water is old and needs refreshing. Even with the addition of chemicals, your hot tub water should be emptied and filled with fresh water every months. If your chlorine or bromine levels are low, it can lead to poorly sanitized water, causing it to go cloudy. Check your waters pH levels to see if they are off-balance. If the water becomes more alkaline, scale can accumulate contributing to the cloudiness of your water.
Most causes of cloudy water are actually caused by what you unknowingly bring into the hot tub. This can be deodorant, moisturiser, even conditioner in your hair or debris from your feet as you enter the spa.
FILTER — Perform a thorough deep clean on your filter see how here or replace the filter cartridge, especially if it is more than 1 year old.
Replace with Antimicrobial filters , which have advanced filter media to inhibit the growth of bacteria. This will be the preventative step to removing clear green water in your hot tub. Retest water chemistry levels including sanitizer and adjust where necessary.
Raise Low Sanitizer Levels Test water for sanitizer level. Depending on sanitizer used, adjust to meet recommended amount. Allow water to circulate for 24 hours then retest and adjust as necessary.
Test weekly to maintain proper hot tub water chemistry. By using test strips to monitor your pH level. Begin by adjusting Total Alkalinity. If TA is low or high, adjust first, which will help regulate pH. Remember, after adding the appropriate chemical, run spa on high speed with blower on if applicable to aerate water. Retest spa water and adjust where necessary.
Maintain proper spa water chemistry by testing weekly. When pH is in balance, follow directions for Excessive Metal Content to remove the green cloudy hot tub water. Share this: Facebook Twitter Pinterest. Like this: Like Loading Leave a Reply Cancel reply Enter your comment here For tackling green spa water, first test the water with test strips to see where the total hardness, total chlorine or bromine, pH, alkalinity, and free chlorine levels are. This is how you know what to adjust.
Keeping these levels in appropriate ranges will help prevent unwanted effects like horrible smells, colors, scums, and more. If the water is green and the sides feel slimy, chances are you have algae in your water.
Tackle algae with chlorine , shock , and cleaning the filter. We recommend to use SpaBoss X-lt if there are excessively hight levels of chlorine or bromine. Additionally, SpaBoss Shock will help to keep chlorine or bromine sanitizers working like they should, keeping organic matter and bacteria from building up.
If you use the hot tub often, use a little more chlorine more often as frequent use can use up chlorine a little faster.
0コメント